Tesi di Dottorato
Permanent URI for this communityTesi di Dottorato
Browse
15 results
Search Results
Item Accuracy aspects in flood propagation studies due to earthfill dam failures(2015-10-30) Razdar, Babak; Costabile, Pierfranco; Costanzo, Carmelina; Macchione, FrancescoFlooding due to dam failing is one of the catastrophic disasters which might cause significant damages in the inundated area downstream of the dam. In particular, there is a need of trustworthy numerical techniques for achieving accurate computations, extended to wide areas, obtained flood mapping and, consequently, at the implementation of defensive measures. In general several key aspects are required for accurate simulations of flood phenomena which are ranging from the choice of the mathematical model and numerical schemes to be used in the flow propagation to the characterization of the topography, the roughness and all the structures which might interact with the flow patterns Regarding general framework discussed before this thesis is devoted to discuss two aspects related to accuracy issues in dam breach studies. In the first part a suitable analytical relation for the description of reservoir have been discussed and the second part the influence exerted by the methods used for computing the dam breach hydrograph on the simulated maximum water levels throughout the valley downstream of a dam, has been investigated. As regards the first aspect, the influence of reservoir morphology on the peak discharge and on the shape of outflow hydrograph have been investigated in the literature. The calculation of the discharge released through the breach requires the knowledge of the water level in the reservoir. It is considerable that the reservoir morphology in computational analyses cannot be expressed exactly by an analytical formula because of natural topography of the reservoir. For this reason, the information about reservoir morphology is usually published as a detail tables or plots which each value of elevation from bottom to top has a corresponding value for lake surface and reservoir volume. However, in the cases for which there is a scarcity of data, analytical expression can be obtained by interpolation of the values of the table. Usually one of the most suitable technique for interpolation data is using polynomial function but unfortunately utilizing this function for solving the problem demand several parameters. Using power function in numerical computations of breach phenomena would be advantageous, because this function is monomial type and only one parameter needs to be estimated. In this thesis, we want to present that this approach is very accurate and suitable to represent the morphology of the reservoirs, at least for dam breach studies. To reach this aim, 97 case studies have been selected from three different geographical regions in the world. The results of this research have been shown that the power function is suitable to obtain an accurate fitting of the reservoir rating curve using a very limited number of surveyed elevations and volumes or areas. Furthermore in this part of the research it has been shown that two points are enough for a good fitting of the curve, or even only one if volume and surface are both available for an elevation close to normal or maximum pool. Results obtained for dam breach calculations using this equation, have the same quality of those achieved using the elevation-volume table. Moreover, this research have been shown that the exponent of power equation can be expressed by a formula which has a precise morphological meaning, as it represents the ratio between the volume which the reservoir would have if it were a cylinder with its base area and height equal to the respective maximum values of the actual reservoir, and the real volume of the reservoir. Regarding the second aspect, over the complexity of the mathematical models which have been used to predict the generation of dam breach hydrograph, it is considerable that the historical observed data of discharge peak values and typical breach features (top width, side slope and so on) have been usually utilize for model validation. Actually, the important problem which should be considered here is traditionally focused on what has been observed in the dam body, because the effects of the flood wave realized in the downstream water levels usually have been neglected. This issue seems considerable because required information for the civil protection and flood risk activities are represented by the consequences induced by the flood propagation on the areas downstream such as maximum water levels and maximum extent of flood-prone areas, flow velocity, front arrival times etc. The water surface data is almost never linked to the reservoir filling/emptying process which can be important information for the estimation of discharge coming from the breach, are available. Moreover, it is quite unusual to have records on the flood marks signs or other effects induced on the river bed, or on the man-made structures, downstream. For this reason finding well documented case study is one of the important part of any simulation study, especially for model validation. One of the few cases in this context is represented by the Big Bay dam, located in Lamar County, Mississippi (USA), which experienced a failure on 12 March 2004. In general analyzing the simplified models for dam breach simulation is the main purpose of this second important activity of the thesis. The simplified model have been utilized in this study, in order to identify a method that, on the basis of the results obtained in terms of simulated maximum water levels downstream, might effectively represent a preferential approach for its implementation not only in the most common propagation software but also for its integration in flood information systems and decision support systems. For the reasons explained above, attention here focuses on the parametric models, widely used for technical studies, and on the Macchione (2008) model, whose predictive ability and ease of use have been already mentioned. To reach this purpose both a 1-D and 2-D flood propagation modelling have been utilizing in this study. The results show that the Macchione (2008) model, without any operations of ad hoc calibration, has provided the best results in predicting computation of that event. Therefore it may be proposed as a valid alternative for parametric models, which need the estimation of some parameters that can add further uncertainties in studies like these.Item Vegetated roofs as a low impact development (LID) approach: hydrologic and hydraulic modeling for stormwater runodd mitifation in urban environment(2016-02-19) Principato, Francesca; Berardi, Luigi; Bertrand-Krajewski, Jean-Luc; Carbone, Marco; Piro, Patrizia; Macchione, FrancescoNei paesi sviluppati, il livello di urbanizzazione è in continuo aumento e dovrebbe raggiungere l’83% nel 2030 (United Nations, 2002; Antrop, 2004). Il notevole incremento della popolazione comporta una continua espansione areale delle città che si traduce nella progressiva cementificazione di aree vegetate sempre più grandi. L’effetto combinato di urbanizzazione (che riduce la disponibilità di spazi naturali e allo stesso tempo modifica la rete di scorrimento superficiale) e cambiamenti climatici (che incrementano la frequenza e l’intensità delle precipitazioni) (Piro et al., 2012) ha comportato una maggiore vulnerabilità delle aree urbane ed uno sconvolgimento del ciclo idrologico naturale. Durante gli eventi di pioggia intensi, i tassi di infiltrazione ed evapotraspirazione si sono notevolmente ridotti, e di conseguenza si è verificato un incremento del volume di deflusso delle acque meteoriche che sovraccarica il sistema di drenaggio urbano (Piro et al., 2012). In un’ottica di sviluppo ambientale sostenibile, nasce quindi l’esigenza di potenziare la rete di deflusso superficiale mediante l’introduzione di soluzioni sostenibili che consentano di rispristinare, per quanto possibile, le condizioni idrologiche che caratterizzavano il bacino prima dello sviluppo urbano (Cannata, 1994). L’insieme di queste tipologie di interventi a basso impatto che, seguendo un approccio ecologicamente basato, consente una gestione delle acque piovane direttamente alla fonte così da prevenire molti problemi che possono accorrere lungo il percorso di trasporto, viene identificato in letteratura con l’acronimo LID (Low Impact Development). Tra queste, la tecnica del verde pensile che protegge, ripristina o imita il ciclo idrologico di pre-sviluppo e, sfruttando gli spazi disponibili sulle coperture a tetto (altrimenti inutilizzate), può essere applicata anche in ambienti urbani densamente edificati, è di particolare interesse ambientale per l’insieme dei benefici che comporta su scala del singolo edificio e del comprensorio urbano circostante (Tillinger, et al., 2006). Diversi studi hanno evidenziato come le coperture vegetate possano avere effetti sulla ritenzione degli eventi di pioggia (DeNardo et al., 2005; VanWoert et al., 2005; Getter et al., 2007; Gregoire and Clausen, 2011), riducendo il volume di deflusso e la portata al colmo (Berntsson, 2010; Palla et al., 2010; Voyde et al., 2010; Stovin et al., 2012) e ritardando il picco di piena (Carter e Rasmussen, 2006; Spolek, 2008). Da queste premesse nasce il seguente lavoro di tesi, che ha riguardato lo studio del Verde pensile come sistema a basso impatto ambientale, per la mitigazione dei deflussi nell’idraulica urbana, focalizzando l’attenzione sulla Modellazione Idrologico-Idraulica: “Vegetated roofs as a Low Impact Development (LID) approach: hydrologic and hydraulic modeling for stormwater runoff mitigation in urban environment”. Il principale obiettivo della ricerca è stato quello di definire, migliorare ed implementare una metodologia per la progettazione dei tetti verdi utilizzando i dati provenienti da diverse aree geografiche (nel caso specifico sono stati analizzati i dati provenienti da due diverse realtà geografiche: Cosenza in Italia e Lione in Francia), al fine di individuare alcuni fattori chiave per la caratterizzazione della risposta di un sistema a verde pensile. Più nello specifico, dopo un’introduzione generale ed una panoramica sui benefici che l’adozione delle LID offre alla gestione delle acque meteoriche in ambiente urbano rispetto ai sistemi convenzionali, nel Capitolo 1 sono stati definiti i principali obiettivi del progetto di ricerca. Tra le soluzioni naturalistiche che operano il controllo della formazione dei deflussi superficiali mediante i processi di ritenzione e detenzione, quella del Verde Pensile viene particolarmente trattata nel Capitolo 2; vengono descritte le componenti stratigrafiche ed illustrati i più importanti effetti benefici conseguibili dall’installazione di coperture vegetate, con particolare attenzione al contributo nella regimazione delle acque meteoriche.Dal momento che la risposta idrologico-idraulica di una copertura vegetata è influenzata da diversi fattori quali le condizioni meteo-climatiche e le caratteristiche costruttive della copertura vegetata, la revisione della letteratura (Capitolo 3) è organizzata in relazione agli obiettivi della ricerca: (1) la prima parte fornisce una panoramica dei modelli per l’analisi del comportamento idraulico dei tetti verdi, visti come strumento di supporto alla gestione quantitativa delle acque di pioggia; (2) nella seconda parte è stata eseguita una ricognizione degli studi scientifici effettuati per analizzare l’influenza dei suddetti parametri sulle prestazioni idrologiche ed idrauliche di una copertura vegetata di tipo estensivo. Tali considerazioni suggeriscono che se il verde pensile deve essere parte delle strategie di gestione delle acque piovane, è fondamentale capire come specifici sistemi di copertura rispondano ad eventi pluviometrici specifici; questo richiede strumenti di modellazione affidabili che consentano di ottimizzare le prestazioni dei sistemi a verde pensile su una vasta gamma di tipi di costruzione e in diverse condizione operative. Come risultato di tali considerazioni, i capitoli 4 e 5 riguardano le sperimentazioni condotte utilizzando due diversi modelli. In particolare il Capitolo 4 indaga l’affidabilità di un modello concettuale di tetto verde, sviluppato congiuntamente dalla Le Prieuré e l’INSA di Lione, per simulare il comportamento di una specifica tecnologia di tetto verde pre-fabbricato (Hydropack® & Stock&Flow®). Il modello si basa sul percorso dell’acqua attraverso quattro serbatoi disposti in serie, ciascuno caratterizzato da uno specifico processo idrologico e/o idraulico rappresentato da equazioni concettuali o semi-dettagliate: Serbatoio di Intercettazione, Substrato, Serbatoio Alveolare ed un Serbatoio di Raccolta. Il modello, adattabile a qualsiasi tipo di copertura attraverso l’attivazione/disattivazione di serbatoi e funzioni opzionali, intende simulare il comportamento dinamico del tetto verde a diversi intervalli di tempo, indagarne l'affidabilità ed ottimizzarne le prestazioni. Il modello è stato testato e calibrato utilizzando un database raccolto su due siti sperimentali, rispettivamente per un anno e nove mesi, misurati al passo temporale di 1 minuto: 1) per l’unità prefabbricata di 1 m2 (Hydropack®) prodotta ed installato a Moisy (Francia) da Le Prieuré, la calibrazione è stata condotta a scala d’evento per valutare il contenuto idrico nel substrato; 2) per il tetto verde a grandezza naturale di 282 m2 presso il Centro Congressi di Lione (Francia),la calibrazione è stata condotta a scala mensile per valutare il deflusso totale in uscita dal tetto verde. Tutte le simulazioni del modello sono state effettuate utilizzando il linguaggio ddi programmazione MatLab. Come indicatori delle performance del modello sono stati utilizzati il criterio di Nash-Sutcliffe (NS) e il Root Mean Squared Error (RMSE). I risultati delle simulazioni effettuate sull’unità Hydropack hanno mostrano che il modello ha una elevata capacità di replicare il comportamento osservato per il contenuto idrico nel substrato durante eventi piovosi, come confermato dagli alti valori di NS (sopra 0,6 per il 78% dei casi, e sopra 0,97 per il 46%) e valori RMSE bassi. I primi risultati hanno inoltre indicato che la risposta del modello è fortemente determinata dal contenuto iniziale di acqua nel substrato (Hs0) che andrà considerato come uno dei parametri chiave del modello quando è usato a scala di evento. Per quanto riguarda le simulazioni mensile effettuate sul tetto verde a scala reale, i primi risultati hanno mostrato una buona capacità del modello di replicare il comportamento osservato per la portata in uscita dal tetto, solo per alcuni eventi; prestazioni inferiori si osservano per alcuni eventi a causa di dubbia affidabilità dei dati o nel caso di eventi con precipitazioni molto piccole. Nel Capitolo 5 viene proposto un modello concettuale (SIGMA DRAIN), sviluppato nel corso del progetto PON01_02543 per simulare il comportamento idraulico della copertura vegetata di tipo estensivo installata nel sito sperimentale dell’Unical. SIGMA DRAIN utilizza, per la simulazione dei fenomeni idrologici e idraulici, il motore di calcolo del software EPA SWMM (Storm Water Management Model), pur essendo completamente svincolato dall’interfaccia utente del software. Il nuovo modello idealizza il tetto verde come un sistema costituito da tre componenti disposte in serie, ognuna caratterizzata da uno specifico processo idrologico-idraulico, corrispondenti ai tre moduli tecnologici principali della copertura: lo strato superficiale è concettualizzato come un sottobacino mentre i successivi strati di terreno e di accumulo sono schematizzati attraverso due serbatoi lineari che descrivono rispettivamente la percolazione attraverso il substrato colturale e il trasporto attraverso lo strato drenante. Un’equazione di bilancio di massa viene applicata a ciascun blocco, tenendo conto dei fenomeni fisici specifici che si verificano in ciascun modulo; il flusso è invece regolato dall’equazione di Richards. Al fine di stimarne l’affidabilità, il modello è stato prima calibrato e poi validato con il software HYDRUS-1D, che modella l’infiltrazione dell’acqua nel sottosuolo; visti i parametri idraulici richiesti dal software, tale operazione ha riguardato essenzialmente lo strato di terreno piuttosto che quello di vegetazione ed accumulo. Osservando i risultati in termini di deflusso dei singoli eventi di pioggia, è possibile constatare che il modello Sigma Drain approssima bene il modello HYDRUS-1D per precipitazioni al di sopra dei 20 mm, mentre per eventi con altezza di pioggia inferiore le performance del modello non risultano soddisfacenti; tale comportamento è attribuibile al fatto che nel modello Sigma Drain, differentemente da HYDRUS-1D, non si tiene conto del contenuto idrico iniziale del substrato. A conferma di ciò, le simulazioni effettuate in continuo, hanno mostrato in media un valore dell’indice di NS pari a 0.8, a dimostrazione che le condizioni idrologicoidrauliche antecedenti l’evento considerato sono rilevanti nella valutazione della risposta del modello. Particolare attenzione è stata riposta all’analisi del coefficiente di deflusso e ai fattori idrologici che sono determinanti nelle performances del tetto quali: la precipitazione, l’intensità e la durata di pioggia, nonché il periodo intra-evento che intercorre tra due eventi indipendenti. A seguito delle simulazioni effettuate con SIGMA DRAIN, dal confronto dei risultati ottenuti in termini di deflusso tra gli eventi di pioggia registrati con passo temporale di 1 minuto sul sito sperimentale dell’Unical e presso Lione, si è evidenziato per entrambi gli scenari un comportamento analogo, stimando un valore soglia delle precipitazioni di 13mm, al di sotto del quale il tetto verde trattiene la quasi totalità dell’evento. Per eventi con altezza di pioggia superiore a 13 mm, è stata rilevata, invece, un coefficiente di deflusso che si attesta in media attorno al 46% e 38% rispettivamente per il set di dati regisrati all’Unical e a Lione; è possibile osservare, inoltre, l’esistenza di una proporzionalità diretta tra precipitazione e deflusso. Per analizzare al meglio l’influenza dei singoli parametri idrologici sull’efficienza idraulica del tetto verde, è stata poi ricavata, con i dati di pioggia dell’Unical, un’equazione statistica sulla base di analisi di regressione lineare multipla, successivamente validata con i dati di Lione, che consenta di avere una prima stima della capacità di ritenzione del tetto verde in funzione della durata dell’evento e dell’altezza di pioggia. In definitiva è possibile osservare che ogni singolo parametro, sia esso idrologico o fisico, apporta un’influenza significativa sulle prestazioni idrauliche di una copertura vegetata. Risulta, dunque, approssimativo valutare l’efficienza di una copertura vegetata mediamente su scala annuale o stagionale, in quanto ogni singolo evento di pioggia, in funzione delle proprie caratteristiche e di quelle della copertura stessa, sarà trattenuto in maniera differente. I risultati ottenuti dalle sperimentazioni hanno evidenziato come la copertura vegetata di tipo estensivo, progettata e realizzata all’Unical, in clima Mediterraneo, presenti un ottima efficienza idraulica anche considerando i dati di pioggia di un’altra realtà come Lione, caratterizzata da un clima Temperato. Infine, nel Capitolo 6 vengono esposte le conclusioni generali sul progetto di ricerca e i possibili sviluppi futuri. Con questo lavoro di tesi, che fornisce indicazioni utili alla realizzazione di una pianificazione urbanistica sostenibile che consenta di attuare una gestione integrata della risorsa idrica, si intende promuovere il verde pensile non solo quale strumento di mitigazione e compensazione ambientale in generale, ma nello specifico quale soluzione di drenaggio urbano sostenibile per il ripristino dei processi fondamentali del ciclo idrologico naturale nell’ambiente urbano.Item Experimental study and qualitative and quantitative modelling of sustainable urban drainage systems (SUDS)(2013-11-27) Mancuso, Antonello; Macchione, Francesco; Piro, Patrizia; Carbone, :Marco; Laucelli, Daniele BClimate changes have become always more frequent, increasing the interest of researchers in finding the causes and, above all, the structural or non-structural solutions to solve the problem. Economic development together with rapid population growth constantly increase the demand of goods and services. As the same as drought, also precipitation became more intense and frequent, even with more ever short duration. These events for their heavy impact are called ‘extreme rainfall events’. The actual management of urban waters is unsustainable thus, foregoing reasons lead to an imperative need to develop new urban ecosystems, requiring a rethink of traditional development techniques. Traditional urban drainage systems are designed to rapidly collect and convey overland flows to the treatment plants, without taking into account of their qualitative characteristics. In order to reach the aim of the qualitative and quantitative control of stormwater in urban areas, a possible way is the widespread implementation in urban areas of ‘blue-green infrastructure’ that provide an holistic and integrated approach to the problem. They are one step beyond other ‘classic’ sustainable urban drainage measures such as LID (Low Impact Development), SUDS (Sustainable Urban Drainage Systems) or BMPs (Best Management Practices), allowing to emphasize their beneficial effects. Use of BGC as a part of sustainable drainage system concept is a winning approach, that allow managing and treatment of stormwater runoff within urban areas, using practices made of green and blue components. Generally green components are represented by any kind of existing vegetation (floral plants, grass, hedges) while the blue one by lakes, ponds, rivers and canals (natural or artificial). Together, these infrastructures allow to create a network between them at regional scale. The real behaviour of these structures is not yet properly modelled. Most of the software currently used in urban hydrology (SWMM by EPA, Music by eWater CRC, etc…) model in a reasonable way the hydraulic behaviour of infiltration practices (such as bioretention cells, infiltration trenches, vegetated filter strips, porous pavement) using a simple mass balance approach. Generation, inflow and transport of pollutants are, instead, determined by the land use assigned to each subcatchments, namely through buildup and washoff laws describing accumulation and washout by either a mass per unit of subcatchment area or per unit of curb length. This approach completely lack of quality algorithms within LID models that take into account of their quality performances as, for instance, reduction of efficiency due to the clogging effect. The clogging phenomenon, described as the decrease in infiltration rate of the soil due to the reduction in soil porosity and hydraulic conductivity, occurs for the majority within infiltration practices such as bioretention cells, infiltration trenches, vegetated swales and permeable pavers. Precisely these latter practices are one of the easiest to implement into urban environment, being aimed to reduce impervious areas and work as ‘link’ within BGCs networks. From these premises the research in the following thesis is developed, whose main objective is to study the implementation of 'blue and green' elements in urban areas and their effect on pollutant loads reduction. Initially, a study of common errors retrieved within a DTM (Digital Terrain Model) has been faced because, if not corrected, they will affect the overland flow network generation and the subsequent hydraulic modelling. DEMs (Digital Elevation Models) can include both terrain elevation data, which commands flow direction of floodwater, and land cover information, which dictates resistance to floodwater distribution. Very often DTMs originate from a variety of ground observations supplemented by various remote sensing techniques (aerial and satellite measurements, total stations, dGPS, aerial LiDAR, terrestrial laser scanning) thus, containing systematic or random errors to individuate and eliminate. A study were carried out to evaluate how DTM resolutions and presence of building affect overland flow network delineation in the Liguori Channel basin, situated in Cosenza (Italy). To achieve this aim, three different DEMs of the study area, generated from different sources, were used: two contour-based DTMs with contour interval respectively of 30 m (DTM 30) and 20 m (DTM 20), and one LiDAR-based DEM, with horizontal resolution of 1 m (LIDAR DTM). Moreover, for a more in depth analysis, LIDAR DTMb (with buildings) cell size has been down sampled from 1 to 5 meters coarse resolution, in order to evaluate also, how cell size affect ponds delineation. Individuation of likely flood areas (ponds) has been carried out using Arc Hydro Tools developed at Centre for Research in Water Resources at University of Texas at Austin. Research highlighted how the correction of DEM generated from LiDAR data and other sources overlapping the buildings (i.e. retrieved from cadas maps) help to diminish the total accumulated water volume into surface ponds, real or spurious, and also that their number does not depend by the raster cell size, but from the accuracy of the source data. Afterwards, a first attempt of best management practices implementation has been carried out within the Liguori Channel situated in Cosenza, Italy. The overland flow network of a highly urbanized sub area has been enhanced through the addition of a certain percentage of green roof and porous pavements. A series of simulations were carried out, using in input the historical annual rainfall series (between 2008 and 2011) and considering a first scenario without LIDs (reference case) and a second scenario with the new practices implemented. Moreover, the same simulation were repeated in continuous, namely considering a single time series composed by 4 years of precipitations (2008-2011) and taking into account, in addition to the two previous cases, of a third scenario where LIDs may deal with clogging phenomenon. In order to perform the EPA SWMM modelling, a ‘residential’ land use has been defined, characterised by build-up and wash off laws for the considered pollutant (Total Suspended Solids – TSS). As regards the green roof and porous pavement simulation parameters, currently these values has been gathered from literature. Within SWMM, the clogging phenomenon is taken into account through a parameter called ‘clogging factor’ that considers the possible decay of LID performance due to the fine material carried by infiltration waters. The empirical formulation is affected by some parameters such as the number of years it takes to fully clog the system (Yclog), the annual rainfall amount over the site (Pa), the pavement's capture ratio CR (area that contributes runoff to the pavement divided by area of the pavement itself), the system's void ratio (VR), the Impervious Surface Fraction (ISF) and the pavement layer thickness (T). The yearly simulation performed show how the percentage reduction of volumes into the network is around 35% on average each year, the mass of Total Suspended Solids is around 30% on average while the relative concentration undergoes an increment around 15%. The latter result can be explained looking at the SWMM runoff quality algorithm. In fact, currently SWMM takes into account of the reduction of pollutants only in terms of reduction of overland flow, due to the lacking of quality algorithms for LIDs simulation. Consequently, the presence of BMPs increases the amount of stormwater that infiltrates, decreasing runoff, therefore the mass of pollutants reaching the sewer outlet. The lower is the volumes of water reaching the sewer, keeping constant the total mass of pollutant over the catchment, the higher is the average outlet concentrations. The results of the continuous simulation are, also, very interesting. While during the annual simulations the trend of volumes for the scenario ‘LIDs with clogging’ ranges always between the other two cases, without and with LIDs, when the continuous simulation is considered, the volumes of the clogged LID are even higher than the volumes occurring without any BMP implemented. The efficiency tends to decrease during time, from 50% when simulation starts to almost 0% at the end of the second year, continuing then to swing around zero per cent for the remaining part of the simulation. In this case, in fact, during the first two simulated years the trend is similar to what it has been found during the annual simulation, while starting from the third year (January 2010), volumes generated for the case ‘LIDs with clogging’ are equal or even higher than those ones generated when no LIDs are used. Although EPA SWMM results are interesting and indicative of LID operation, they are not very accurate, especially concerning the qualitative simulation of the stormwater management practices. For this reason, later, the research has been focused on improving the qualitative simulation algorithms, with particular attention to porous pavements. Data collected into an experimental laboratory rig of three different and widely used permeable pavement types has been analysed. The investigated systems were: monolithic porous asphalt (PA), modular Hydrapave (HP), and monolithic Permapave (PP). The rig, made of three vertical compartments in which the three porous pavers stratigraphies has been rebuilt, has been subjected to a semi-synthetic hyetograph, made of five different rain intensities (wetting regime) plus several drying periods. From the frequency curve typical of Brisbane (AU), in correspondence of different percentile ranges four flow rates has been chosen (A, B, C, D). In addition, a 1 in 5 year storm of 5 min duration was selected; this represents the typical design storm where the porous pavers are likely to be developed. The accelerated laboratory test allowed to simulate 26 years of operation under Melbourne climate. About the water quality monitoring, an intense sampling regime has been conducted in which samples were collected from inflow and outflow and analysed for Total Suspended Solids (TSS), Total Phosphorus (TP) and Total Nitrogen (TN). Afterwards, a correlation analysis has been performed in order to individuate the key variables affecting the porous pavement functioning. According to these results, the key variables identified to affect the pollutant concentration values were: the cumulative flow every 6, 12 and 24 hours before the sampling time, the cumulative inflow volume in each time step and the cumulative trapped mass. Initially, it has been tried to analyse the phenomenon through the ‘k-C* model’, that is a conceptual model used to simulate the pollutant behaviour through the system, based on a first-order kinetic decay equation. Notwithstanding the wide popularity and tested applicability on various other treatment practices such as sand filters, wetlands, ponds, infiltration systems and vegetated swales, the model did not show satisfying results when applied to porous pavements, especially about heavy metal and total nitrogen modelling. The predictive power of the model has been assessed through the calculation of the Nash–Sutcliffe model efficiency coefficient, widely adopted in the Anglo-Saxon world to evaluate behaviour and performance of the hydrologic models. Nash-Sutcliffe coefficient is an indicator of the model’s ability to predict about the 1:1 line between observed and simulated data. NSE ranges between −∞ and 1.0 (1 inclusive), with NSE = 1 being the optimal value. Values between 0.0 and 1.0 are generally viewed as acceptable levels of performance, whereas values < 0.0 indicates that the mean observed value is a better predictor than the simulated value, which indicates unacceptable performance. Considering this, the concentration data collected has been processed, also taking into account of the correlation analysis previously carried out, which allowed to estimate the concentrations of the main pollutants such as TSS (Total Suspended Solids), TP (Total Phosphorous) and TN (Total Nitrogen) to the output section of the porous pavements. The reliability of the new proposed formulas has been demonstrated both by high values of the Nash- Sutcliffe coefficients, always positive, and also by very low errors (between 10% and 25%) among modelled and measured concentrationsItem Sulla modellazione dei deflussi di un corso d'acqua naturale per una migliore tutela dell'ambiente e protezione del territorio(2010-10-21) Alfano, Monica; Penta, Andrea; Macchione, FrancescoItem Sostenibilità della gestione delle risorse idriche(2006) Pantusa, Daniela; Veltri, Paolo; Maiolo, MarioItem Modelli ecoidrologici per la descrizione dei flussi energetici, di CO2 e di dinamica della vegetazione in ambiente mediterraneo(2009-10-28) Cervarolo, Giuseppe; Mendicino, Giuseppe; Macchione, Francesco; Telesca, VitoItem Contributo alla riossigenazione naturale della zona eufotica dei corpi idrici dovuto all'attività fotosintetica(2010-10-27) Nigro, Gennaro; Macchione, Francesco; Frega, Giuseppe; Infusino, ErnestoItem Taratura e verifica di un modello averaged di evoluzione di una spiaggia con duna(2007-10-30) Gencarelli, Rosanna; Veltri, Paolo; Tomasicchio, Giuseppe RobertoItem Contributo alla valutazione del dissesto idrogeologico nel bacino sperimentale Bonis:stima dell'incertezza spaziale del fattore di erodibiltà del suolo K(2007-10-30) Falace, Mario; Veltri, Paolo; Frega, Giuseppe C.Item Ottimizzazione della gestione di sistemi multi-invaso a scopo plurimo: il caso del sistema Ariamacina-Cecita-Muone(2010-10-27) Zimbo, Fabio; Macchione, Francesco; Mendicino, Giuseppe; Principato, Giancarlo